Theres money in magnetos Editor’s note: Once again we tip our hats to Hank Henke for his service to the indus- try. During the recent ERA Show he made a presentation on the lost art of magneto rebuilding. The response to his presentation was overwhelmingly positive and we are pleased to print a transcript of the session in this issue of the Exchange. y name is Henry Henke. I have United Starter & Alternator in Indiana and have been in the business for about 30 years. I started my career as a mechanic when I was 15 years old. The man I went to work for got tired of me asking questions. The first job I had was scrubbing parts with a bucket of gasoline and kerosene, and I’d scrub them and I’d say, “What’s this?” “Where does this go?” “What does this do?’ His comment was, “Do you ever run out of questions?” I won’t promise you I’ve got all the answers, but we have a gentleman over here, John Brillman from The Brillman Company. They are a supplier of magneto parts. If I can’t answer your questions ’’m sure he can (brillman.com, [888] 274- 5562). Good guy to know. The other one that sells magneto parts is Standard Magneto in Chicago, Ill. They are proba- bly the largest supplier of magneto parts in the country. Their website is standard- magneto.com and phone number is (800) 624-6386. Their whole catalog is online. A very knowledgeable man by the name of Rich at Standard Magneto is the man that I talk to when I have a problem. He can tell you before you even stick your fingers in a magneto, “Don’t mess with that one because there’s no parts, you’re not going to find any parts. If you break a screw you’re going to own that magneto.” Or he’s going to tell you, “Yeah, I’ve got all the parts for it and do what you’ve got to do.” There’s money to be made in doing magnetos. It’s not a big dark secret about how they work or anything else. It’s pretty straightforward. What I do on pricing them when I rebuild them is get the price of a rebuilt or a new magneto. I figure out I could buy this magneto for a $250 and if I’m going to sell it to somebody I’m going to mark it up 40 percent. So that’s my tar- get figure. Now take the magneto apart, and see that I only have $50 worth of parts. It gives me a lot of leeway because I’m going to sell it for what I would sell the rebuild unit for if I bought it outright. Why should I sell it for anything less? And that money goes in my pocket. I am not embarrassed to charge for what I do. This is not a hard thing for me. You do not need a lot of spe- cial equipment. You will need a small press; hand impact driver; quarter-inch socket set or nut driver set; screw driver; small puller; light hammer; a feeler gauge and a five- eights-inch socket to remove the impulse retaining nut. With these tools you will be able to disassemble the magneto. Some magnetos have gear drive. All of them have to have some kind of pulse. Take the gear off, they’re all pretty much the same. So how do you test them? I had a plug made that I’ll pass around. This plug allows me to spin the magneto on my lathe. I made a bracket for my lathes, to bolt the magneto on. Now that’s two special parts. The third special tool is a spark plug rack so I can make sure all cylinders fire. I have the spark plugs set at .060—twice the gap it normally is. I talked to John the other day, and he said you really want to go a quarter inch. So I will redo my settings next time I run one. OK, we have taken the gear off the front; the next thing is you’ve got to impulse. This impulse is on a tapered shaft in most cases. Do not try to pry it off with screwdrivers because you’re not going to get it off. You know how difficult it is to get the tapered pulley apart—same thing here. That’s why you need a little puller. All you have to do is put just a little pres- sure on the impulse and tap on the puller lead screw with a hammer and it’ll pop right off. Underneath there is usually a lit- tle woodruff key; you’ve got to get that out of the way. Now what are we going to do? On a Fairbanks-Morse you have a metal washer, a rubber seal, and another metal washer. You have to remove these pieces to access the wire retaining ring. This wire serves two purposes; it holds the bearing in the housing and the shaft to the bearing. Fail- ure to remove the wire clip will lead to a broken housing. Now we need to work on the other side or the magneto. You see the breaker plate which also has the rotor shaft on it. ’’m going to pass around these two gears. See if you can find the timing marks. Before you start taking things apart, there are tiny timing marks you want to make sure that you locate. The small gear has a tooth ground at an angle and the big- ger gear doesn’t happen to have any marks on it. So that one is a good example of why you have to mark it some way so you know you’re going to get that gear back in the same relationship when you put it back. Magnetos defined According to “Bosch Automotive: A product history,” a magneto is an ignition devic