Get the complete system analysis picture By Albin Moore H ow many times have we had a vehicle in for what the customer thought was a charging system problem? We hook a voltmeter to the electrical sys- tem and find low charging voltage and pos- sibly excessive voltage ripple. We replace the generator, only to find that the real problem is a defective battery or a poor elec- trical connection. Wouldn’t a picture of what is happening in the starting and charging system be a great way to keep mistakes like these from happening? Over the years, I have tested a lot of bat- teries with both a carbon pile tester and a capacitance tester. I have had many batter- ies pass these conventional tests, only to fail a few days or weeks later. This has driven me to rethink starting and charging system testing. I am always looking for quicker and more accurate ways to test in order to gain more information faster. Let’s take a look at a 2005 Ford Freestyle. The vehicle is in the shop for an oil change service. The odometer shows 60,000 miles. There are no starting com- plaints, though when we started the engine in the parking lot, we noticed a slower than normal cranking speed (the engine did not spin up as fast as it should have). The vehi- cle is five years old with the original bat- tery. In the shop, we hooked a voltage lead to the battery terminals and clipped a high amp current probe around the negative bat- tery cable, and the engine started. I use an oscilloscope, high amp current probe and a voltage test lead. This testing takes approximately five minutes, includ- ing hooking the current probe around a battery lead, testing the voltage across the battery terminals and running the engine for two minutes while graphing the voltage and current that is going either in or out of the battery. The current probe needs to be hooked to a place that will be able to test all of the current going in and out of the bat- tery, but it makes no difference whether it is on the positive or negative cable. In my experience, the negative battery cable is the best and easiest place to hook the current probe. With these two quick hookups, you are able to run a relative compression test, test the ability of the battery to produce energy, check the integrity of the starter motor cir- cuits and examine the charging ability and the integrity of the generator. Any graphing multimeter or scope will work for this test, so you can use what you have in the shop. Do not use a digital multimeter (DMM) with min/max, because the capture rate is too slow. Besides, a DMM will not draw a picture. I have labeled the scope a video voltmeter, because it draws a picture of the voltage and amperage of the starting and charging systems. In this case, a picture is worth a thousand words. With this testing, we are looking for the minimum battery voltage when the starter solenoid is closed (inrush voltage), and for the maximum amperage that the starter will draw before the motor starts turning. We can zoom in and take a look at the integrity of the starter solenoid contacts as they close, the operation of the starter motor, the maximum charge rate of the generator when the engine starts and the minimum charge rate after the engine has been running for two minutes. With all of this information, it is easy to see exactly what is happening in the starting and charging system. It also is easy to perform a relative compression test while the scope is hooked up. All that is needed on most cars is to depress the throttle to the floor and crank the disabled engine for a few seconds. There are two important numbers I look for with this test: an inrush voltage of not less than 8.5 volts, and a minimum charge rate of 3 amps or less after charging for two minutes. An inrush voltage below 8.5 volts is a good indication of a weak battery, and a continual charge rate above 3 amps is a great indication of a sulfated battery (bad battery). The only way a sulfated battery can be found in its early stages is with a current probe monitoring the current going into the battery. A carbon pile load test or a capacitance tester will not find this prob- lem. Consider what an extra 10 or 15 amps of current load will do to the life of a gen- erator. If a sulfated battery is found, more testing needs to be done to find out the rea- son the battery sulfated. As batteries age, this is a normal process. But if the battery is only a year or so old, most likely a prob- lem in the electrical system has caused this condition. Some of the causes could be the parasitic draw is too high, which is dis- charging the battery ovemight with the generator having to charge the battery once the engine is started, or a voltage regulator that is causing the generator to overcharge the battery. The Ford’s battery, as seen in Figure 1, has an OCV (open circuit voltage) of 12.54 volts, which is good, but a minimum intush voltage of 7.83 volts, which is not good. As the starter is energized, the starter current spi
File Type:
pdf
File Size:
3 MB
Categories:
eren