ERA Office: Monday – Friday 9:00-5:00 CST

275 W. BROWN ST, UNION, MO 63084

636-584-7400

office@electricalrebuilders.org

ERA Tech Helpline: 636-584-TECH (8324)

Active pulleys are here to stay By Connard Cali Editor’s note: Thanks to Connard Cali of FACET for sharing the notes from his popular presentation at this year’s Electrical Rebuilder’s Association Show. For more information on active pulleys, visit posi- tork.com. W: hear this all the time: “Solid pulleys have been around for years, they are cheap, and they do the job just fine. Now these ‘active’ pulleys are showing up on newer cars, they are expen- sive, and they don’t do much when I final test the alternator on the bench. Active pulleys are just pulleys, they are all the same, and I doubt this pointless idea is going to be around for long.” We had the same exact thoughts when we first started looking at active alternator pulleys. But curiosity got the best of us, so Interesting, we thought, but combustion engines and alternators have been around for years. Why are active pulleys needed now? To answer that question, keep in mind that the crankshaft speed of any internal combustion engine is not uniform. During the power stroke the crankshaft speeds up while during the compression stroke the crankshaft slows down. Naturally, as a result, the belt speeds up and slows down accordingly. And, the longest lull between combustion events happens at engine idle. Further, the fewer the cylinders in the engine, the fewer the load cycles per crank revolution (6-cyl:3 pulses/crank revolution vs. 4-cyl:2 pulses/ crank revolution), and thus the less uni- form the crankshaft rotation. In other words, the fewer the cylinders, the more torsion- ally active is the engine. The component along the belt path that offers the greatest resistance to speed U.S. Active Pulley Fleet [Clutch Pulley Vehicles gy Decoupler Pulley Vehicles ( Total Active Pulley Vehicles | 50,000,000 45,000,000 40,000,000 35,000,000 30,000,000 25,000,000 20,000,000 15,000,000 10,000,000 5,000,000 2006 2007 2008 Figure 1 Calendar Year 2009 2010 2011 2012 we instrumented a few late model cars and checked things out for ourselves. For each car we mounted a solid pulley, then a clutch pulley, then a springy decoupler- Isolating Decoupler Pulley DP). The data we collected surprised us: these things work and there were big differences between them once they were working in the car! Intrigued by these results, we sched- uled several trips to Detroit to meet with OE vehicle and alternator manufacturers. Lo and behold we learned the long list of technical reasons for active alternator pul- leys. More importantly, we learned that the majority of new engines from Ford, Chrysler, GM, Toyota, Hyundai, and oth- ers will use active alternator pulleys, specifically IDP pulleys only. The IDP fleet size in the U.S. is expected to grow by eight to 10 million IDPs per year start- ing MY2011 (Figure 1): change, or rotational inertia, is the alterna- tor. The large mass of the rotors spinning at approximately three times the engine speed, combined with the induced mag- netic field during charging, determine the level of resistance to changing engine speeds. In other words, the larger the alter- nator, the more resistant it is to engine speed changes. You can easily conclude that the trend for fuel economy means fewer cylinders. To maximize power and torque for these engines, OEs are employing multiple technologies (e.g. ECOBOOST, etc.) that intensify the crankshaft speed changes between combustion events at or near idle. Further, engine idle speeds have also been aggressively reduced for the sake of fuel economy. Now, the increasing electrical demands posed by the systems in newer vehicles require larger output alternators. Whereas in the past a 90A unit was commonplace, today 160A+ units are common. In fact, OEs are heading to 200A+ units. Further, advances in alternator technology empow- er them to reach ever higher percentages of maximum rated output at engine idle. The results, of course, are alternators that are ever more resistant to engine speed changes at or near idle. Now, combine the trend in engines with the trend in alternators in newer vehi- cles. You can see that these trends are irreconcilable. Left unchecked, newer vehicles would have huge belt tension fluctuations, breakage, high radial loads on all bearings along the FEAD, prema- ture wear and vibration of the tensioner, excessive alternator brush wear/bounce, varying alternator outputs, infant failures in electronics, among other problems. These high frequency issues, of course, are difficult to see with the naked eye, yet they exist, are measureable, and cause damage. But then again, high voltage is also not visible, but it exists, is measurable, and can cause damage. In fact, below is some data taken from a very late model Chrysler 4-cylinder engine. The first set of data shows the belt forces and tensioner movement when the correct (active) pulley is used. The second set of data on the same engine show the same forces and movement when an incorrect pulley is used. Look at the scales on the axes and imagin

File Type: pdf
File Size: 3 MB
Categories: eren