ERA Office: Monday – Friday 9:00-5:00 CST

275 W. BROWN ST, UNION, MO 63084

636-584-7400

office@electricalrebuilders.org

ERA Tech Helpline: 636-584-TECH (8324)

Key-Off Parasitic Battery Drain What’s normal? BY BOB THOMAS Ke, parasitic drain on a vehicle’s battery is becoming an ever increasing problem, as auto manufacturers continue to add electrical gadgets and the modules needed to control them. There was a time, not so long ago, when there were no electronics, and the only key-off battery drain was from the electromechanical clock, assuming that the vehicle had one. Strange as it may seem, if that clock ever quit working, there was a good chance that it would draw a lot more current than normal, and it could even drain the battery overnight. Today’s vehicles are a different matter altogether, with the advent of the body control module (BCM) that directly manages almost every accessory that is not related to operating the engine or the transmission. This includes all interior and exterior lighting, windshield wipers and washers, audio and video systems, alarm systems, electric windows, door locks and power seats—basically any accessory that comes with the vehicle. Many of these devices are programmed to stay on for a period of time after the key and the engine are switched off—all for your convenience. By using a BCM and smaller electronic modules, such as switches and timers for each device, the vehicle manufacturers can make any of the accessories do just about anything a new car owner’s heart desires. But all of this comes with a cost—a parasitic drain on the battery whenever the vehicle is not being used. Nearly all cars and trucks on the road today have some parasitic drain, just like those cars from the 50s and 60s had with those clocks—only today, parasitic drains are a lot more complicated. Let us say that a customer is having a problem with the battery going dead after it sits over night or over a long weekend. How do you test the parasitic drain on the battery—what is normal and how much drain is too much? These are three good questions we will try to answer. Testing Parasitic Drain The normal parasitic drain on most vehicles is in the 20 to 50 milliamp range. A milliamp is 1/1,000 of an amp. We say normal here to mean “as it comes from the factory” without any add-on aftermarket accessories. We will get back to aftermarket accessories later. So to test for current which is that low, you need a meter that is capable of reading milliamps. Most good multi- meters can do that, but the problem is that you need to disconnect the battery to put that multi-meter in line. When you disconnect the battery, there is a chance that an excessive and problematic parasitic drain related to electronics, will disappear and not return until the engine is put through a start cycle. Of course, you cannot start the vehicle through a milliamp meter, so you need a meter with a sensitive inductive pickup called a low- current probe. If you are servicing vehicles, installing batteries or replacing alternators, you really need one of these testers. Excessive parasitic drain is a battery killer and Ww ow £ E Figure 1—Battery drain on the 2002 Nissan Sentra test vehicle immediately after engine shutdown. can cause alternators to be stressed repeatedly. The only way you can be sure that your battery and/or alternator will not be subjected to this abuse, is to routinely check for parasitic current drain with every installation, whether you suspect a problem or not. This type of meter will allow you to test parasitic drain very quickly, anytime you install a battery. Prices for a stand-alone probe start at about $125. You can also buy a low-current probe that will plug into some multi-meters. To measure the drain, first make sure that all of the cables and connections at the battery are clean and tight. Then run the engine for a short period of time, shut it off, remove the key from the ignition and close the door. If there is an under- hood light, you can disconnect or disable it after you have made sure that it goes off when the hood is closed. Keep in mind that you are measuring the amount of current that is flowing out of the battery. You can do this from either side, positive or negative, but you have to test every cable on the side that you choose. The negative side is usually the easiest. Simply place the probe over the cable as shown in Figure 1. If you are quick enough, you will be able to watch the parasitic drain drop as accessories time out. Some vehicles will completely shut down in as little as a few minutes. Others, particularly high-end vehicles with more accessories, can take as long as 30 minutes. You must allow enough time for everything to time out. You may even want to walk away and work on something else while you wait. The number on the meter, at the end of the test, is your parasitic drain. The vehicle we used in the photos is a 2002 Sentra. The initial parasitic drain, after the engine was shut off, was .063 of an amp or 63 milliamps. As you can see, the actual drain, after everything had shut down was .016 of an amp or 16 milliamps

File Type: pdf
File Size: 4 MB
Categories: eren